Gpcalero's Spartan Build
#11
Great thread!!
Your rig is looking great. Gotta warn you though, the mods never end, LOL. I just took ours to the shop today for LED lighting in the engine bay, the undercarriage, the wheel wells and behind the spare tire on the back tailgate. Dark blue lights all around for shows inside (ie AutoRama in Detroit in February).
If you wheel much you'll probably want to look into UCP (undercarriage protection) and rock sliders. You can search on this forum.....some of the guys make and sell some great stuff on here.
Good luck with everything.....even school!!
Your rig is looking great. Gotta warn you though, the mods never end, LOL. I just took ours to the shop today for LED lighting in the engine bay, the undercarriage, the wheel wells and behind the spare tire on the back tailgate. Dark blue lights all around for shows inside (ie AutoRama in Detroit in February).
If you wheel much you'll probably want to look into UCP (undercarriage protection) and rock sliders. You can search on this forum.....some of the guys make and sell some great stuff on here.
Good luck with everything.....even school!!
#12
Great thread!!
Your rig is looking great. Gotta warn you though, the mods never end, LOL. I just took ours to the shop today for LED lighting in the engine bay, the undercarriage, the wheel wells and behind the spare tire on the back tailgate. Dark blue lights all around for shows inside (ie AutoRama in Detroit in February).
If you wheel much you'll probably want to look into UCP (undercarriage protection) and rock sliders. You can search on this forum.....some of the guys make and sell some great stuff on here.
Good luck with everything.....even school!!
Your rig is looking great. Gotta warn you though, the mods never end, LOL. I just took ours to the shop today for LED lighting in the engine bay, the undercarriage, the wheel wells and behind the spare tire on the back tailgate. Dark blue lights all around for shows inside (ie AutoRama in Detroit in February).
If you wheel much you'll probably want to look into UCP (undercarriage protection) and rock sliders. You can search on this forum.....some of the guys make and sell some great stuff on here.
Good luck with everything.....even school!!
#13
So this next mod was supposed to be plug and play. And for the most part it was. The LED smoked taillights didn't quite fit flush when we tried to install them.
The body panels (sheet metal) meet behind the taillights and are welded together, form a 45 degree angle and slightly protrudes towards the back of the taillight unit. This was causing clearance issues with the new lights so we ground the excess sheet metal in a 2 inch section on each side about a cm. Brushed it up a bit more with some sand paper and applied some metalsealer then repainted the ground down area to match the body.
I love the new look.
Plasti-Dip is up next!
More to come...
The body panels (sheet metal) meet behind the taillights and are welded together, form a 45 degree angle and slightly protrudes towards the back of the taillight unit. This was causing clearance issues with the new lights so we ground the excess sheet metal in a 2 inch section on each side about a cm. Brushed it up a bit more with some sand paper and applied some metalsealer then repainted the ground down area to match the body.
I love the new look.
Plasti-Dip is up next!
More to come...
#15
So far it's gonna be the front grille, tow hooks, rims, & badges. I'll post it up tomorrow!
#17
I'm up in Clearwater but I go down there to see my girlfriend at fgcu which I assume that's where you go too. We should go wheeling sometime when I'm down there. Idk where the little mud holes and rock quaries are down there so you'll have to show me around.
#18
For sure man. Send me a PM.
#19
Plasti-dipping isn't all that hard with the gun. There is just a lot of prep. Do it right and it comes outs 10x better than plastidip from the can.
First up were the GM chicklet badges and the H3 badges on both sides.
Then we did the tow hooks...
Front hooks.
All in all. For the badges and hooks I did a good 8-10 coats each. The gun sprays finer than the can does and the finish is a lot better too (smoother & consistent throughout).
Next up is the front grill and wheels.
Stay tuned...more to come.
First up were the GM chicklet badges and the H3 badges on both sides.
Then we did the tow hooks...
Front hooks.
All in all. For the badges and hooks I did a good 8-10 coats each. The gun sprays finer than the can does and the finish is a lot better too (smoother & consistent throughout).
Next up is the front grill and wheels.
Stay tuned...more to come.